Resealing Steering Rack
Home Up

 

 

 

Rack Resealing

If you're considering what it takes to fix your Porsche power steering then this is a  good place to start. Its a very good idea that you do some research because this  little job is easily and often underestimated. I know this because I've made every mistake  possible and am therefore somewhat qualified to warn you of the many pitfalls. The information on this page is NOT complete - I do not have re-assembly instructions. Those would require many more hours of work than I have to offer. Still, you can get a good idea of what is involved by reading through the disassembly areas that I have here.

At the outset, I should tell you that resealing a rack will be somewhere between  moderately difficult and I'm-so-pissed-at-this-I'll-just-get-rid-of-the-car. I'm  tempted to tell you it is sooo easy and that all you need is a little determination but I'm afraid this casual confidence will get a few of you in over your head and if that happens you'll be looking to lure me into a dark alley. Please review these "Ten  Things to Know ... " before you begin stalking me.

======   Six Things to Know before Attempting to Reseal Your Steering Rack =====
1) It is moderately difficult to get the rack out of the car and this provides  potential for a fair amount of exasperation. Its even worse on the turbos. Even if things go very well, it will take over an hour just for removal. Another hour (plus) to get the rack re-installed. yes, there are people that can do if faster.

2) Unless you have a hydraulic test stand, you'll have to re-install the rack in order to test for leaks and to make sure the rack works. If problems arise, you may have to  remove it a second time to correct. This sucketh greatly. On the upside, doing the actual reseal is really just disassembly, inspection and re-assembly. Well with the reach of a determined and patient motor-head.

3) Its possible that once you get the rack apart, you will find that you need parts that are not included in your reseal kit. ZF, (a German company with a long name)  makes the rack and pump for our cars. ZF will not deal with anyone other than Porsche  dealers for mini-parts. This means that your source for parts is very limited to reseal kits. Most of the parts are included in the kit but the kits include the most commonly needed parts.   

4) Some basic tools are needed, a clean place to work, a way to clean up the rack and parts,  some sort of vice, and a variety of sockets, extensions and tools to replace the  seals. 

5) If the main shaft is is pitted, your new seals will not last very long.

6) Steering racks are a relatively simple mechanism but one which relies on hydraulic  pressure. Many "reseals" fail because problems with particulate contamination are not  corrected. This is one reason that many "rebuilt" racks are warranted for only 12 months.
=====================================================

 

 

 

This (above) is likely to be what you first see when you begin looking for the source of your hydraulic fluid leak. The fluid will probably be coming from one or both of the boots and may also be coming from the small hole in the picture. The hole should have  a rubber or plastic dust plug in it (the plug is only intended to keep dust out, not to keep fluid in).  Normally, there should not be fluid in this cavity. This hole is here so that when an alignment of the steering is done, the mechanic can visually confirm that the rack is centered. In the hole you can see a small dimple (almost hidden by shadow), the dimple indicates the rack center point (wheels should be straight ahead). 

 

Some un-official nomenclatures.


Introductory Notes: 

At the very minimum, the rack and all of its' components  should be completely disassembled, cleaned and inspected prior to re-assembly. It is likely that the inspection will reveal smaller problems that contributed to the seal failure. These should be dealt with. 


 

Other Symptoms:

Aside from leaks, there are other ways the rack can fail. The most likely is a groaning that occurs when you first begin to turn the steering wheel. Groaning can also be caused in two ways; one, by air in the system (which is usually associated with a leak in the lines leading to the rack) or a bad seal in the control tower casting. 


Rack Removal

  • Place the car on jack stands (front only) or ramps.

  • Disconnect the battery.

  • Mark the outer tie rod ends (a touch of spray paint or a crayon) .

  • Pull back the rack boots from the rack (careful, they may be full of fluid).

  • Inspect the exposed portion of the main shaft - this will give you a first indication of a worn or damaged shaft.

  • Disconnect the outer tie rod ends (use 2 wrenches to loosen jam nut and then turn the inner tie rod until the rod separates). Be careful to leave the jam nuts as undisturbed as possible so to help with minimize mis-adustments to toe-in.

  • Remove the alternator (OK to leave wiring attached, but get it clear of its normal location ).

  • Remove steering shaft coupler bolt. (Use a chisel to slightly open up the coupler - careful, the racks control valve is absorbing the blows).

  • Mark the splined rack shaft (so that the steering wheel can be correctly re-oriented  during installation).

  • Center the steering wheel.

  • Disconnect the pressure line from the pump & drain.

  • Loosen the 4 rack mounting bolts (one cannot be completely separated due to  interference from the pressure line).

  • Separate the steering shaft coupler from the splined rack shaft.

  • Disconnect the return line from its rack fitting.

  • Lift the rack clear of the suspension cross-member and other obstructions and begin long-rack disassembly.



Long-Rack Disassembly

  • Remove the equalizing line (black plastic tubing and fittings - careful, fittings are brittle and do not usually come with "kits."

  • Remove the mounting brackets and grommets.

  • Remove the rubber pressure line and the other hard lines. Drain these. A hex key is best but a pipe wrench (a rather crude tool) will remove the fitting bolts. Use it only as a last resort.

  • Remove the return line banjo bolt (aka hollow screw) and fitting, copper crush rings should be replaced. These are available at many good hardware stores. Note later models have a different fitting for the return line.

  • Place the rack in vice, (keep the jaws of the vice on the control tower casting and away from the pressure lines)  and remove (2) the tie-rods (note: these are usually very  tight;  they have right-hand threads. There is a flange that may have been peened (hammered in  such a way to prevent loosening). Filing or grinding of the flange may be needed to loosen the tie-rod. 

  • Set the boots aside and drain (if needed) and begin Rack Disassembly. 

  • Mark the tie rods (driver's side and passenger's side so you will know which goes to which side of the rack during re-assembly). 


Rack Disassembly

  • With the rack still in the vice, loosen the collar nut ( right hand threads). If you're using a hammer and a drift, take care not to damage the cylinder.

  • Remove the rack from the vice.

  • Separate the rack cylinder.


  • Using a small pick and a pair of needle nose pliers, gently remove the guide ring from the end of the cylinder. If you forget to remove the guide ring at this time, the ring will be damaged when the seal is driven out of the rack cylinder.  Your ring will then look like the one above. Note, the photo shows a damaged guide ring and the guide pad .

  • Mark the orientation of the splined shaft to the tower, getting it back in this orientation is critical to having a centered steering wheel. The steering can be repositioned either by removing it or via an alignment.

  • Remove the three 10 mm bolts from the top of the control tower and set it aside.

  • Remove the control tower cover and seal.  

  • Grasp the splined end of the control valve and pull gently (while turning CCW) to remove the control valve & pinion  assembly from the tower. Photo shows the original orientation of bearings and shims.

  • Remove the (2) 10mm bolts from the bottom of the control tower casting.

  • Remove the small cover and hidden spring.

  • Extract the guide pad piston, a special tool may be needed.

  • Carefully remove the guide pad from the piston.

  • Separate the main rack from the control tower.

 

  • Remove the seal from the upper tower cover.

  • Separate the shuttle assembly from the main rack shaft. Note the tool is the foreground is a seal puller - not absolutely required.



Control Tower Disassembly

 

  • Place the tower casting in a vice and observe the installation depth of the roller bearing cap. Gently drive the pinion bearing  and cap out through the  bottom of the tower. Set the bearing aside for cleaning/inspection.

  • Turn the casting over in the vice and access the lower control valve seal via the  pinion bearing hole. Drive the seal out through the top of the casting.

  • Remove the small rubber plug from the centering pin hole.


Shuttle Disassembly

 


  • Remove the o-ring, nylon ring, & snap ring from the shuttle cylinder.

  • Drive or press the seal out of the shuttle cylinder. The seal will be "backed" by a  bronze or nylon guide ring. Observe it's orientation, as one side is rounded and one side squared.


Mainshaft Disassembly

 


  • Carefully, remove the snap rings, seal ring & o-rings. These pieces should be removed  from the end away from the rack's teeth. Note how there is an o-ring under the blue seal ring (this is typical of all seal rings - they must be supported  by an o-ring). Be careful when removing the snap rings - it cannot be allowed to scratch the shaft.


Inspecting and Polishing The Mainshaft

  • The mainshaft is the most expensive part of the rack. Its' surface is critical to long  seal life. In almost all cases the shaft should be polished to return it to a scratch-free condition. Normally, pits cannot be polished out and will quickly destroy  a seal. A skilled machinist can weld a pitted shaft and then machine it back to original tolerances.


  • Polishing is not something I would attempt by hand. Here, I have set up a drill press to rotate the shaft. I then simply  use a wet or dry paper (1000 or 1500 grit) to wet-sand small scratches out of the shaft's  surface, finish with either 2000 grit or buffing compound. A well equipped machinist can do a much better job for about $25. The above picture is taken from a flood damaged car - beware, this sort of thing is frequently sold on EBay.


 
Cleaning 

 

  • All metallic parts should be cleaned in a mild solvent (white gas or lacquer  thinner). Plastic (nylon) parts should be cleaned with dish soap,  (stronger  solvents will make them brittle).
     
    Other cautions: Many of the fasteners and parts of the Porsche are cadmium covered as a form of corrosion control. We tend to want to clean everything perfectly and many of us have found that a wire wheel (mounted on a bench grinder) works well for this. For cadmium covered parts, this is an extremely bad idea. Cadmium is carcinogenic - it causes cancer. Beware, cadmium is a life altering substance and can EASILY get into your bloodstream where it will then damage your kidneys. Kidneys are extremely difficult to change.

 

 

Follow this link to some discussion of the power steering hoses.